V0.2-S1 Kit by LDO Motors (Rev.A+) | ||||
Thank you for purchasing the Voron 0.2r1 Kit! Before you dig in, we recommend double checking all the parts in the checklist below. Please contact your vendor if any parts are missing. | ||||
If you are new to building Vorons, be sure to check out the following essential resources: - Get the latest design files and assembly manual from Voron's 0.2r1 repo: https://github.com/VoronDesign/Voron-0 - Log on to Discord and get help from Voron's active community: https://discord.gg/voron - Check the LDO documentation site for info specific to our kit: https://docs.ldomotors.com/en/voron/voron02 - Follow the software setup guide after completing the physical build: https://docs.vorondesign.com/build/software/ |
||||
Box | Item | Qty. | Check1 | Check2 |
Build Plate & Parts | Aluminum Build Plate, 120x120mm | 1 | ||
PI Film Heater (Installed), 24VDC 100W, w/ Thermal Fuse | 1 | |||
Spring Steel Flex Plate, 120x120mm, Textured | 1 | |||
Heater Cover Plate (Installed) | 1 | |||
Magnetic Pad, 120x120mm | 1 | |||
Die Springs, Yellow, 8x4x20mm | 3 | |||
Bed Thermistor, Screw Type (for heat bed) | 1 | |||
Drag Chain, 7x7mm | 1 | |||
Electronics | Heatsink for Raspberry Pi | 1 | ||
Raspberry Pi 4B (OPTIONAL item, confirm with your reseller whether the RPi is included) | 1 | |||
Bigtreetech SKR Pico | 1 | |||
MicroSD Card, 16G | 1 | |||
Blower Fan, 3010, 24V | 2 | |||
Axial Fan, 3010, 24V | 2 | |||
AC Inlet | 1 | |||
Fuse, Slow Blow, 250VAC 2A | 2 | |||
Bowden Tubing, 4x3mm | 1 | |||
Zip Ties, 3x150mm | 100 | |||
A+ Kit (V0.2R1 Upgrade) 2x M2x10 self Tapping Screw 1x MR85 Bearing 1x Microswitch w/ Cable 1x ECAS04 Bowden Collet |
1 | |||
Fasteners, Tools & Misc | Shim Washer, 6x3x0.5mm | 55 | ||
Hex Nut, M3 | 155 | |||
Slide in Nut, M3 | 100 | |||
Lock Nut, M3 | 6 | |||
Machine Screw, SHCS, M2x6 | 75 | |||
Machine Screw, FHCS, M2x6 | 12 | |||
Machine Screw, SHCS, M2x8 | 12 | |||
Machine Screw, BHCS, M2.5x6 | 6 | |||
Machine Screw, BHCS, M3x6 | 63 | |||
Machine Screw, FHCS, M3x8 | 7 | |||
Machine Screw, BHCS, M3x8 | 135 | |||
Machine Screw, BHCS, M3x10 | 55 | |||
Machine Screw, BHCS, M3x12 | 33 | |||
Machine Screw, BHCS, M3x16 | 12 | |||
Machine Screw, BHCS, M3x25 | 12 | |||
Machine Screw, BHCS, M3x30 | 12 | |||
Machine Screw, BHCS, M3x35 | 33 | |||
Machine Screw, BHCS, M3x40 | 12 | |||
Machine Screw, SHCS, M3x50 | 2 | |||
Self-tapping Screw, M2x10 | 35 | |||
T Nut, 15x5.4x1.5 | 3 | |||
Thumb Nut, M3, 304 | 3 | |||
Heatset Insert, Brass, M3x5x4 | 60 | |||
Tape, VHB | 1 | |||
Rubber Feet, 14x11x9mm | 4 | |||
Magnets, Neodymium, Round, 6x3mm | 10 | |||
Brass Insert Solder Tip | 1 | |||
Drill bit, 2mm | 1 | |||
Hex Wrench, 1.5mm | 3 | |||
Hex Wrench, 2mm | 1 | |||
Hex Wrench, 2.5mm | 1 | |||
Slot head screwdriver, 2.5mm | 1 | |||
Frame Kit | LDO V0 Frame kit | 1 | ||
LDO-1515-VRN200A, 10 pcs LDO-1515-VRN200B, 4 pcs LDO-1515-VRN200C, 2 pcs LDO-1515-VRN200D, 4pcs LDO-1515-VRN100E, 4pcs |
||||
Linear Rail Kit | M2 T Nut for Linear Rail | 5 | ||
LDO Stainless Steel Linear Rail (LDO-SLR7H-1R-150Z0) (If the linear rail you receive is not pre-greased, please remember to grease it.) |
4 | |||
HIWIN Linear Rail (MGN7H-1R-150Z1) | 1 | |||
Motor Kit | LDO V0.2 Motor Kit | 1 | ||
LDO-36STH20-1004AHG(VRN), E Motor, 1 pc LDO-35STH52-1504AH(VRN), AB Motor, 2 pcs LDO-42STH25-1004CL200E(VRN), Z Motor, 1 pc Anti Backlash Nut, T8, 18x24mmOD, 1 pc |
||||
Panels | Side Panel 211mm x 229mm x 3mm Acrylic, Clear | 2 | ||
Front Door 212mm x 239mm x 3mm Acrylic, Clear | 1 | |||
Rear Panel Top 211mm x 63mm x 3mm Acrylic, Clear Black | 1 | |||
Rear Panel Bottom 211mm x 185mm x 3mm Acrylic, Clear Black | 1 | |||
Mid panel 3mm Acrylic, Matte Black | 1 | |||
Motor Panel 3mm Acrylic, Matte Black | 1 | |||
Deck Panel 3mm Acrylic, Matte Black | 1 | |||
TopHat Side Panel 3mm Acrylic, Clear | 4 | |||
TopHat Top Panel 3mm Acrylic, Clear | 1 | |||
Toolhead & Motion | Bondtech Drive Gear Kit | 1 | ||
Setscrew M4*4 DIN916 | 5 | |||
Setscrew M3*2 DIN916 | 3 | |||
Teflon Tube, 4x2mm | 1 | |||
Thumb Screw Assembly | 1 | |||
Bearing, MR85 | 2 | |||
Bearing, F623-RS | 24 | |||
Pulley GT2 20T (6mm wide) (5mm bore) | 2 | |||
Open Belt, GT2, 6mm | 4 | |||
Machine Screw, SHCS, M3x30, Partially Threaded | 2 | |||
Machine Screw, SHCS, M3x35, Partially Threaded | 3 | |||
Other | Kirigami Bed Mount Kit | 1 | ||
Other | Picobilical PCB Kit | 1 | ||
Other | LDO V0.2 Cable Kit | 1 | ||
Other | Mornsun Power Supply, 200W, 24V | 1 | ||
Other | C13 Power Cord | 1 | ||
Other | E3D Revo Hotend LDO Edition, with 0.4/0.6mm 2 nozzles | 1 | ||
Other | PVC Wire Duct, 20Wx25H | 0.33 |