Refer to the Part Printing Guidelines section of the official assembly manual for general print settings. For the latest parts files, visit the Voron Github repository. If you do not have the means to print your own parts in ABS, the Voron Print It Forward program is a great option to obtain the parts at a very reasonable cost. If you do plan on printing the parts, refer to the following directions for LDO kit specific options:
- Purple - These are not optional and must be printed for our kit to work.
- Blue - These are optional parts/changes that improve fit, appearance, or quality of life.
¶ Main Printed Parts
- Cable Chain Parts - Our cable chains use the same 2 hole configuration as igus cable chains. When printing parts that interface with cable chains, always use the igus version instead of generic (e.g. z_bearing_block_right_igus instead of z_bearing_block_right_generic).
- grill_rear_left - Our kits ship with 1.2mm AC inlets with integrated switches. We recommend printing this part instead of the original grill_rear_left or grill_rear_left_filtered.
- 3030_wire_clip - We recommend printing about 6-9 of these clips, which come in handy for cable management.
- foot_tpu - Rubber compressor feet are provided in the kit, no need to print this part.
- heatbed_terminals_cover - We designed an alternative part that allows for heatbed cables extend both backwards and sideways.
- y_belt_anchor - Our printer will use sensorless y homing, print the y_belt_anchor_sensorless file instead of the normal y_belt_anchor.
- Counterweight Wheel - Print this optional wheel and fit it over your counterweight idler bearings to help prevent the kevlar cable from slipping off.
- WAGO Mount - Our kit includes 3 WAGO terminals for wiring mains wires. Print this mount to fix the WAGOs onto an extrusion (use 2 M5x10 screws).
- Controller Mount - Our kit ships with the Bigtreetech SKR mini e3, the corresponding pcb mount is skr_mini_e3_mount.
- 5V PSU mount - Our kit requires the 5V switching power supply to be mounted vertically, a custom mount for this purpose can be found here.
- 24V PFC Mount - EU users may receive the LMF350-23B24UH slim power supply, a mount for this power supply can be found here. All other users should use the standard 24V power supply mount parts here and here.
- LED Splitter Mount - Our kits ship with LED strips and an LED splitter PCB. print this part to mount the splitter PCB to the side panel.
Rev.C kits are designed to work with Voron Stealthburner toolheads. The kit also includes the Nitehawk toolboard for easy wiring. Follow the instructions below to ensure you print the correct parts for this kit:
- Stealthburner - This kits work with a full Voron Stealthburner toolhead. Also bundled is the E3D® Voron Revo. However, check with your vendor on which hotend (if any) is actually shipped. Make sure to use the Voron Revo printhead here.
- Clockwork 2 - This kit ships with parts to build a standard Clockwork 2 extruder. Parts for the Clockwork 2 are found here.
- Nitehawk Toolboard - Our kit includes the Nitehawk toolboard, which will work with standard Clockwork 2 parts (or Galileo 2 if you purchased this mod). In particular, you will need the pcb spacer and the toolhead cover).
- USB Adapter Mount - The USB adapter works in conjuction with the Nitehawk toolboard. This part works as the mount for the USB adapter. Use 3 M3x10 SHCS screws to install the cover onto the base - the screws thread directly into the plastic.
Our kits now ship with BigTreeTech 4.3" touch panels. Follow the instructions below to ensure you print the correct parts for this kit:
- Grill Front Left - The front left grill has been modified to mount the touch panel. The part can be obtained here.
- Grill Mid Section - This modified front mid-section grill removes the old 12864 LCD mount feature. An optional insert can also be printed and fits into the middle of the grill.
- Touch Panel Case - The touch panel case consists of three parts: the case, the mounting plate, and the button cap.
- Steppy Keychain - Last but not least your kit comes with the steppy mascot keychain kit, you will need these printable parts.